This equipment is MIK-1 chain blunt repair design, (18806749158) automatic operation, the chain knife after processing period of time, the chain will have a blunt edge phenomenon, this operation MIK-1 and current when power will be significantly improve, inconvenient to use, and to cause MIK- life a rather affected, and therefore in need of repair has produced blunt blade, in order to obtain the best results the device again. 5 Maintenance:? Prior to any maintenance operation unplug the power! 5.1 machine maintenance:? When not in use should keep the machine clean. Keep all connections and slider rails clean. Add machinery lubricants (30 #).? Promptly clean water tray wastewater. 5.2 storage and scrap processing:? If the machine is not a long time should be thoroughly cleaned. The metal parts coated with anti-rust and cleaned up oil. ? The machine in a dry environment to prevent corrosion and aging. ? The machine parts are no toxic effects. When this machine is scrapped because of the machine completely dismantled and plastic parts and metal parts separated, with the correct manner. 6 Fault and service:? The failure rate of the machine is very low, generally for the replacement of wearing parts. ? When the machine does not work, check the power connection is secure. ? The main power switch is not open, close the main power switch. ?? Sensor is damaged, replace the sensor. ? The machine is not reset and start pressing the stop button, reset. ? Grinding wheel prolonged use or damaged, replace with a new standard grinding wheel. ? Work does not light, check and replace the lights. ? If you have other questions, please contact our service personnel. ? Dear customer, we have to be honest and trustworthy, humane management for the purpose, committed to producing high-quality products woodworking machinery industry. The control system uses the entire international high-end intelligent sensor control, overload. Overcurrent protection, automatic and manual switch freely, just that you press the start button, automatic grinding chain week. And add lighting and automatic cycle cooling water control. Stepper motors and linear guides are used imported materials, other accessories are in line with national standards, to ensure the stability and life of the machine. Over the years, our products of its stability, more accurate characteristics of the majority of customers of all ages. A. Product introduction 1. Product Type / Name 1.1 XFJ-01 / repair machine 1.2 Technical parameters of the chain width:? 16mm Chain Length:? 648 mm wheel speed:? 2800r / min Wheel Size:? Φ150 * Φ32-6 / WA100L input voltage? : 220V / 230V 50 / 60Hz input power:? 260W full load current:? 1.25A machine size:? 660 * 400 * 580 Total Weight:? 73Kg 2 machine uses:? This machine is a slot machine repair lock R groove in the chain developed a machine. When the chain cutter cutting wood, often time running fever chain cutter, edge wear, such as the continued grooving, the motor resistance is too large, easy to burn out the motor also reduces the efficiency of the slot. Use repair machine repair chain, restored chain cutter R groove, click the Start button, automatic grinding R groove within a week (80 teeth), guarantee a sharp edge, improve the slotting efficiency, but also reduces the lock slot machine maintenance costs, is your ideal choice. ? 3 safety rules: a) This machine is suitable for 16mm "chain blade repair b) subject to this machine we have a confirmed repair chain cutter can operate correctly conform to the description shown include all operations.? maintenance and repair provisions, and contains provisions that safe operating manual suggests. 2? Never change any part of the machine, this will lead to insecurity.? Before the preparatory work, make sure that all parts of the machine has been installed, the wheel and R contacts within the chain cutter depth appropriate? Do not put the machine on the outside when rain or damp places, or placed around flammable liquids or gases.? Do not pull the power cord to move the machine method, do not use pull Methods unplug the power cord.? damage out plug or power cord must be replaced immediately off.? Avoid excessive bending power lines, particularly in the transport and storage should pay attention to this. Do not wound the power of the machine on.? The machine stored in a dry safe place and do not allow children to touch.? This machine is only applicable to the age of eighteen and who clearly and risk factors mentioned in the description to use. Maintenance work is only allowed to be done by us authorized sales and service personnel.? must take into account national security requirements and related rules of safety knowledge.? Any unauthorized changes or modifications harm caused by the manufacturer is not liable, the user bear 4 Installation and Operation:? Connect the power supply before starting to use, check the supply voltage to meet the requirements on the nameplate of the machine turn on the power switch on the wheel installation and amended to remove the wheel motor shaft nut, replace it.?.? The new wheel, tighten the nut wheel angle correction consistent with the chain cutter in the R angle (Wheel Size Φ150 * Φ32-6 / WA100L).